13th International Conference on Fracture June 16–21, 2013,Beijing, China -11- that application of the pre-strain should only be used if the mechanical loading is applied in stress-controlled cases. References [1] Schulze V. Modern Mechanical Surface Treatment – States, Stability, Effects. Wiley-VCH Verlag GmbH &Co. KGaA. 2006. [2] Altenberger I, Nalla RK, Noster U, Liu G, Scholtes B. Residual tress stability and near-surface microstructures in high temperature fatigued mechanically surface treated Ti-6Al-4V. Materialwissenschaft und Werkstofftechnik, 34 (2009) 29 – 541. [3] Liu J, Yuan H. Prediction of residual stress relaxations in shot-peened specimens and its application for the rotor disc assessment. Materials Science and Engineering, A 527 (2010) 6690–6698. [4] V. Mertinger, E. Nagy, F. Tranta, J. Sólyom, Strain-induced martensitic transformation in textured austenitic stainless steels. Materials Science and Engineering: A, 481–482 (2008) 718-722. [5] S.S.M. Tavares, D. Gunderov, V. Stolyarov, J.M. Neto, Phase transformation induced by severe plastic deformation in the AISI 304L stainless steel. Materials Science and Engineering: A, 358 (2003) 32-36. [6] S.K. Ghosh, P. Mallick, P.P. Chattopadhyay, Effect of cold deformation on phase evolution and mechanical properties in an austenitic stainless steel for structural and safety applications. Journal of Iron and Steel Research, International, 19 (2012) 63-68. [7] G.B. Olson, M. Cohen, Kinetics of strain-induced martensitic nucleation. Metallurgical Transactions A, 6 (1975) 791-795. [8] R.G. Stringfellow, D.M. Parks, G.B. Olson, A constitutive model for transformation plasticity accompanying strain-induced martensitic transformations in metastable austenitic steels. ActaMetallurgica et Materialia, 40 (1992) 1703-1716. [9] PO Santacreu, JC Glez, G Chinouilh, T Frölich. Behaviour model of austenitic stainless steels for automotive structural parts. Steel Research International, 77(2006) 686-691. [10] A.M. Beese, D. Mohr, Effect of stress triaxiality and Lode angle on the kinetics of strain-induced austenite-to-martensite transformation. Acta Materialia, 59 (2011) 2589-2600. [11] J.L. Chaboche, A review of some plasticity and viscoplasticity constitutive theories. International Journal of Plasticity, 24 (2008) 1642-1693. [12] J. Lublin. Plasticity theory. Pearson Educational Inc., 2006. [13] Socie DI, Marquis GB. Multiaxial Fatigue, SAE International, Arrendale, 2000. [14] C.J. Miao et al. Investigation of low-cycle fatigue behavior of austenitic stainless steel for cold-stretched pressure vessels. Journal of Zhejiang University- Science A (Applied Physics and Engineering), 14(2013): 31-37. [15] Z. Mei, J.W. Morris, Influence of deformation-induced martensite on fatigue crack propagation in 304-type steels, Metallurgical Transactions A, 21 (1990) 3137-3152. [16] A. Das, S. Sivaprasad, M. Ghosh, P.C. Chakraborti, S. Tarafder, Morphologies and characteristics of deformation induced martensite during tensile deformation of 304 LN stainless steel. Materials Science and Engineering: A, 486 (2008) 283-286. [17] K. Mumtaz, S. Takahashi, J. Echigoya, Y. Kamada, L. F. Zhang, H. Kikuchi, K. Ara, M. Sato, Magnetic measurements of martensitic transformation in austenitic stainless steel after room temperature rolling. Journal of Materials Science, 39 (2004) 85– 97. [18] W.S. Lee, C.F. Lin, The morphologies and characteristics of impact-induced martensite in 304L stainless steel, ScriptaMaterialia, 43 (2000) 777-782. [19] G. Hu, C.C. Xu, J.G.Yuan, Deformation induced martensite transformation and its magnetic memory effect of austenitic 304 stainless steel. Nondestructive Testing, 30(2008)216-219. [20] Y.X. Ren, The comparison test of α-phases of austenite and ferrite austenite double phases of stainless steel,Physical Testing and Chemical Analysis Part A:Physical Testing, 41(2005) 184-185. [21] C.C. Xu, X.S.Zhang, G.Hu, Microstructure change of AISI304 stainless steel in the course of cold working. Journal of Beijing University of Chemical Technology (Natural Science Edition), 29(2002) 27-31. [22] J. Talonen, P. Aspegren, H. Hanninen, Comparison of different methods for measuring strain induced alpha' -martensite content in austenitic steels, Materials Science and Technology, 20 (2004) 1506-1512. [23] C.C Young, Transformation toughening of phosphocarbide-strengthened austenitic steels. Doctoral thesis, Massachusetts Institute of Technology, Cambridge, MA, USA, 1988.
RkJQdWJsaXNoZXIy MjM0NDE=