13th International Conference on Fracture June 16–21, 2013, Beijing, China -9- implying that there was no influence of hydrogen up to the yield stress of the steel; 3. There were surface cracks in the necked region on the specimens tested under hydrogen charging, implying that the influence of hydrogen was associated with the final ductile fracture process after the onset of necking. Acknowledgements This work is supported by an ARC linkage grant & Alstom (Switzerland) Ltd. References [1] S. Ramamurthy, W.M.L. Lau, A. Atrens, Influence of the applied stress rate on the stress corrosion cracking of 4340 and 3.5NiCrMoV steels under conditions of cathodic hydrogen charging, Corrosion Science, 53 (2011) 2419-2429. [2] S. Ramamurthy, A. Atrens, The influence of applied stress rate on the stress corrosion cracking of 4340 and 3.5NiCrMoV steels in distilled water at 30 °C, Corrosion Science, 52 (2010) 1042-1051. [3] E. Villalba, A. Atrens, Hydrogen embrittlement and rock bolt stress corrosion cracking, Engineering Failure Analysis, 16 (2009) 164-175. [4] E. Gamboa, A. Atrens, Stress corrosion cracking fracture mechanisms in rock bolts, Journal of materials science, 38 (2003) 3813-3829. [5] E. Gamboa, A. Atrens, Environmental influence on the stress corrosion cracking of rock bolts, Engineering Failure Analysis, 10 (2003) 521-558. [6] R. Rieck, A. Atrens, I. Smith, The role of crack tip strain rate in the stress corrosion cracking of high strength steels in water, Metallurgical and Materials Transactions A, 20 (1989) 889-895. [7] A. Oehlert, A. Atrens, Stress corrosion crack propagation in AerMet 100, Journal of materials science, 33 (1998) 775-781. [8] A. Atrens, A. Oehlert, Linearly-increasing-stress testing of carbon steel in 4 N NaNO3 and in Bayer liquor, Journal of materials science, 33 (1998) 783-788. [9] A. Atrens, Z. Wang, ESEM observations of SCC initiation for 4340 high strength steel in distilled water, Journal of materials science, 33 (1998) 405-415. [10] M. Wang, E. Akiyama, K. Tsuzaki, Effect of hydrogen and stress concentration on the notch tensile strength of AISI 4135 steel, Materials Science and Engineering A, 398 (2005) 37-46. [11] M. Wang, E. Akiyama, K. Tsuzaki, Effect of hydrogen on the fracture behavior of high strength steel during slow strain rate test, Corrosion Science, 49 (2007) 4081-4097. [12] L. Marchetti, E. Herms, P. Laghoutaris, J. ChAne, Hydrogen embrittlement susceptibility of tempered 9%Cr-1%Mo steel, International Journal of Hydrogen Energy, 36 (2011) 15880. [13] E. Villalba, A. Atrens, An evaluation of steels subjected to rock bolt SCC conditions, Engineering Failure Analysis, 14 (2007) 1351-1393. [14] E. Villalba, A. Atrens, SCC of commercial steels exposed to high hydrogen fugacity, Engineering Failure Analysis, 15 (2008) 617-641. [15] Q. Liu, B. Irwanto, A. Atrens, The influence of hydrogen on 3.5NiCrMoV steel studied using the linearly increasing stress test, Corrosion Science, (2012) DOI: 10.1016/j.corsci.2012.10.019. [16] A. Atrens, C. Brosnan, S. Ramamurthy, A. Oehlert, I. Smith, Linearly increasing stress test (LIST) for SCC research, Measurement Science and Technology, 4 (1993) 1281. [17] N. Winzer, A. Atrens, W. Dietzel, G. Song, K. Kainer, Comparison of the linearly increasing stress test and the constant extension rate test in the evaluation of transgranular stress corrosion
RkJQdWJsaXNoZXIy MjM0NDE=